Mobility Scooter Chargers

Foldalite Trekker - Replacement Lithium Charger

The multifunctional Impulse II battery charger is suitable for mobility scooters and electric wheelchairs. Most mobility scooters are fitted with two 12-volt batteries which are connected in series.Together they generate a current of 24 volts. The Impulse II is suitable for 24 volts and a variety of batteries, such as GEL batteries, AGM batteries and wet batteries. The Impulse II combines versatility with safety. For example, the battery charger has double insulation and is protected against reversed polarity, overvoltage and overheating. The Impulse II’s compact and lightweight design allows you tostore it without any problem in a shed or storage space. The charger can be quite easily moved or taken with you. A reliable battery charger with a long service life. There is a rubber bumper available for the Impulse II Battery Charger. The IP65 Charger is already protected against dust, and water spray - now you can protect it from accidental damage too. This rubber bumper allows it to withstand the knocks and bangs of workshop life. It will extend the life of your charger, and it has an easy-carry handle, ...or hang it from a hook when not in use. Mobility and independence are the keywords when it comes to using an electric wheelchair or scooter; the freedom to decide for yourself where to go. So of course, it’s important to be able to take your mobility scooter with you. To this end, you can rely on smart solutions from Victron Energy XLR plugThe Impulse II comes with a so-called “XLR plug” which is the universal standard for mobility scooters and electric wheelchairs. Specifications Input voltage: 230 VAC (range 180-265 VAC) Frequency: 50/60 Hz (range 45-65 Hz) Efficiency: 95% Power consumption in no-load operation: 0.5 W Charge voltage 'absorption': 28.8 V Charge voltage 'float': 27.6 V Charge voltage ‘storage': 26.4 V Charge algorithm: 4-stage adaptive Charge current: 6A Minimum battery capacity: 40AH Protection: Reverse polarity, output short circuit, Over temperature Weight: 1.3Kgs Dimensions (h x w x d): 60 x 105 x 190 mm Adaptive 4-stage charge algorithm: bulk – absorption – float – storageThe Impulse II charger features a microprocessor-controlled ‘adaptive’ battery management system. The adaptive feature will automatically optimize the charging process relative to the way the battery is being used. Storage mode: less maintenance and ageing when the battery is not in useThe storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode, float voltage is reduced to 2,2V/cell (26,4V for a 24V battery) to minimize corrosion of the positive plates and loss of liquid due to gassing. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulfation, a major cause of early battery failure. Protected against overheatingOutput current will reduce as ambient temperature increases up to more than 30°C, but the charger will not be disabled.Two LED’s for status indicationRed LED: bulk, absorptionGreen LED: float, storage en repeated absorption (refresh)Both LEDs flashing: connected with reverse polarity, short circuit, over-voltage The Impulse II is a battery to set your mind at ease. It has a fully automated charging programme which optimises battery recharging. This 4-phase charging curve guarantees the best possible service life for your battery. During the charging process, the charger goes through three different phases. The first sees high-power charging of the battery up to approx. 80% capacity. The last 20% or so is charged at lower power as part of the second phase. The third and final phase ensures that the batteries stay fully charged. During the last phase, you can disconnect the charger from the mobility scooter.

A reliable battery charger with a long service life. There is a rubber bumper available for the Impulse II Battery Charger. The IP65 Charger is already protected against dust, and water spray - now you can protect it from accidental damage too. This rubber bumper allows it to withstand the knocks and bangs of workshop life. It will extend the life of your charger, and it has an easy-carry handle, ...or hang it from a hook when not in use. Mobility and independence are the keywords when it comes to using an electric wheelchair or scooter; the freedom to decide for yourself where to go. So of course, it’s important to be able to take your mobility scooter with you. To this end, you can rely on smart solutions from Victron Energy The multifunctional Impulse II battery charger is suitable for mobility scooters and electric wheelchairs. Most mobility scooters are fitted with two 12-volt batteries which are connected in series. Together they generate a current of 24 volts. The Impulse II is suitable for 24 volts and a variety of batteries, such as GEL batteries, AGM batteries and wet batteries. The Impulse II combines versatility with safety. For example, the battery charger has double insulation and is protected against reversed polarity, overvoltage and overheating. The Impulse II’s compact and lightweight design allows you tostore it without any problem in a shed or storage space. The charger can be quite easily moved or taken with you.   XLR plugThe Impulse II comes with a so-called “XLR plug” which is the universal standard for mobility scooters and electric wheelchairs. Specifications Input voltage: 230 VAC (range 180-265 VAC) Frequency: 50/60 Hz (range 45-65 Hz) Efficiency: 95% Power consumption in no-load operation: 0.5 W Charge voltage 'absorption': 28.8 V Charge voltage 'float': 27.6 V Charge voltage ‘storage': 26.4 V Charge algorithm: 4-stage adaptive Charge current: 8A Minimum battery capacity: 50AH Protection: Reverse polarity, output short circuit, Over temperature Weight: 1.3Kgs Dimensions (h x w x d): 60 x 105 x 190 mm Adaptive 4-stage charge algorithm: bulk – absorption – float – storageThe Impulse II charger features a microprocessor-controlled ‘adaptive’ battery management system. The adaptive feature will automatically optimize the charging process relative to the way the battery is being used. Storage mode: less maintenance and ageing when the battery is not in useThe storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode, float voltage is reduced to 2,2V/cell (26,4V for a 24V battery) to minimize corrosion of the positive plates and loss of liquid due to gassing. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulfation, a major cause of early battery failure. The Impulse II is a battery to set your mind at ease. It has a fully automated charging programme which optimises battery recharging. This 4-phase charging curve guarantees the best possible service life for your battery. During the charging process, the charger goes through three different phases. The first sees high-power charging of the battery up to approx. 80% capacity. The last 20% or so is charged at lower power as part of the second phase. The third and final phase ensures that the batteries stay fully charged. During the last phase, you can disconnect the charger from the mobility scooter. Protected against overheatingOutput current will reduce as ambient temperature increases up to more than 30°C, but the charger will not be disabled.Two LED’s for status indicationRed LED: bulk, absorptionGreen LED: float, storage en repeated absorption (refresh)Both LEDs flashing: connected with reverse polarity, short circuit, over-voltage

Economy Mobility Charger - 24 Volt (2A) - Lithium Please note that this charger will only work with lithium batteries

Pro-Lite Professional Waterproof (IP68) 24v Mobility Battery Charger - 4AThis waterproof Ultra Charger has been developed for the use in harsh environments, and in situations where water may be present. It is able to charge any lead-based battery, including Gel-, AGM-, Wet- and Ca- battery types. It utilises a 5-step charging program and safely functions in a fully automatic mode. The output of the charger is electronically protected against short circuit, reverse polarity connection and deeply discharged batteries. It is fitted with coloured LEDs which are used to indicate charging status and errors.Features:Battery type: (Gel, AGM, Wet or Ca) built-in profilesDistinctive warning of battery being in a state of deep dischargeSignalling of possible connection problems with battery terminalsOutput power is reduced automatically at high temperaturesIndication of a non-chargeable ‘dead battery’ conditionRemote battery temperature sensing / charge voltage compensationLEDs to indicate operation and charging status5-step charging technology with automatic restart chargingShort circuit and reverse polarity protectionAutomatic shut-off at high temperaturesConvection cooled

The Numax Charger is very easy to use and gives you peace of mind that your batteries will be checked and charged accordingly. The battery simply connects to the charger using the 3-pin plug and everything else is taken care of. This charger is designed to bulk charge as well as float charge making it one of the leading chargers on the market today. Once your batteries have been charged they are then maintained by the Numax Charger so that you are fully ready to go at any time with the knowledge that your batteries are fully ready to go too! This type of charger also projects benefits forward as it ensures your batteries are maintained in peak condition, saving time, energy, money and fuss in the future. Other benefits of the Numax Connect are that the charger has deep charge recovery, fast cycle charge and automatically turns on and off- everything you need to keep your batteries at optimal charge and condition.Features     Easy to use     Maintains and charges batteries     Maintains batteries in peak condition     Deep charge recovery     Fast cycle charge     Automatically turns on and off Specifications     Output Voltage: 24V     Output Current: 4Amp     Length: 155mm     Width: 70mm     Height: 48mm     Weight: 500g

This Numax Connect & Forget automatic charger is easy to use and hassle free. Just connect the battery to the charger using the 3 PIN PLUG, and turn it on.The Numax Connect & Forget battery charger will check the state of the battery and employ the correct charging regime accordingly.This charger is specially designed to bulk charge as well as float charge, making it one of the leading chargers in today's mobility market. Once the battery has been charged it will be maintained by the charger, making sure it's in peak condition when you need it to be. Using this type of charger will prolong the life of your battery, saving you time and money in the future.FeaturesDeep Discharge RecoveryFast Cycle ChargeLong Term Battery MaintenanceAutomatically turns on and offSpecificationsOutput Voltage: 24VOutput Current: 7AmpLength: 167mmWidth: 103mmHeight: 50mmWeight: 900g

Suitable for lead acid batteries only. For use with car, motorcycle Mobility and lawn mower batteries.Portable and robust heavy duty battery chargers with LED’s to show current charging levels, double insulated and protected against thermal overload and reverse battery connection.12V 6A automatic battery chargerSuitable for lead acid batteries onlyCar, motorcycle and lawn mower batteriesPortable and robust heavy duty battery chargersLED’s to show current charging levelsDouble insulated and protected against thermal overload and reverse battery connectionCharge rate 4.2ADC (6A RMS)

Economy Mobility Charger - 24 Volt (5 Amp) Suitable for most Mobility Scooters or electric wheelchairs with batteries between 30-50ah. Features Input Voltage: 100-240V AC Overput Voltage: 24V DC Max Charge Current: 5 Amp Fitted With a 3 Pin XLR Plug (Fits 99% of Mobility Products) Fully Automatic Charging Short Circuit Protection

OverviewGood quallity charger for small mobility scooters.DimensionsOverall Length - 12.5cm (5")Overall Width - 6.7cm (2.5")Overall Height - 14cm (5.4")SpecificationsTotal Weight - 0.4kgsInput Voltage - 100-240 Volt ACOutput Voltage - 24Volt DCMax Output Current - 2 AmpShort Circuit Dectection - YesReverse Poloraity Protection - YesOverheat Protection - TBARecomended Battery AH - 7-17AHWarranty - 1 YearWarranty Type - Return to baseManual Supplied - Yes

Fused and fully moulded UK 3-pin plugs to IEC 320 cold condition sockets. The mains leads are rated at 10A and are manufactured from 1mm 2 approved cableVoltage rating AC: 240VConnector type A: UK Mains PlugConnector type B: IEC PlugCable type: 3 CoreColour: BlackNote: Make sure you fit the correct fuse for the appliance you are using. Max 10A