The multifunctional Impulse II battery charger is suitable for mobility scooters and electric wheelchairs. Most mobility scooters are fitted with two 12-volt batteries which are connected in series.Together they generate a current of 24 volts. The Impulse II is suitable for 24 volts and a variety of batteries, such as GEL batteries, AGM batteries and wet batteries. The Impulse II combines versatility with safety. For example, the battery charger has double insulation and is protected against reversed polarity, overvoltage and overheating. The Impulse II’s compact and lightweight design allows you tostore it without any problem in a shed or storage space. The charger can be quite easily moved or taken with you. A reliable battery charger with a long service life. There is a rubber bumper available for the Impulse II Battery Charger. The IP65 Charger is already protected against dust, and water spray - now you can protect it from accidental damage too. This rubber bumper allows it to withstand the knocks and bangs of workshop life. It will extend the life of your charger, and it has an easy-carry handle, ...or hang it from a hook when not in use. Mobility and independence are the keywords when it comes to using an electric wheelchair or scooter; the freedom to decide for yourself where to go. So of course, it’s important to be able to take your mobility scooter with you. To this end, you can rely on smart solutions from Victron Energy XLR plugThe Impulse II comes with a so-called “XLR plug” which is the universal standard for mobility scooters and electric wheelchairs. Specifications Input voltage: 230 VAC (range 180-265 VAC) Frequency: 50/60 Hz (range 45-65 Hz) Efficiency: 95% Power consumption in no-load operation: 0.5 W Charge voltage 'absorption': 28.8 V Charge voltage 'float': 27.6 V Charge voltage ‘storage': 26.4 V Charge algorithm: 4-stage adaptive Charge current: 6A Minimum battery capacity: 40AH Protection: Reverse polarity, output short circuit, Over temperature Weight: 1.3Kgs Dimensions (h x w x d): 60 x 105 x 190 mm Adaptive 4-stage charge algorithm: bulk – absorption – float – storageThe Impulse II charger features a microprocessor-controlled ‘adaptive’ battery management system. The adaptive feature will automatically optimize the charging process relative to the way the battery is being used. Storage mode: less maintenance and ageing when the battery is not in useThe storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode, float voltage is reduced to 2,2V/cell (26,4V for a 24V battery) to minimize corrosion of the positive plates and loss of liquid due to gassing. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulfation, a major cause of early battery failure. Protected against overheatingOutput current will reduce as ambient temperature increases up to more than 30°C, but the charger will not be disabled.Two LED’s for status indicationRed LED: bulk, absorptionGreen LED: float, storage en repeated absorption (refresh)Both LEDs flashing: connected with reverse polarity, short circuit, over-voltage The Impulse II is a battery to set your mind at ease. It has a fully automated charging programme which optimises battery recharging. This 4-phase charging curve guarantees the best possible service life for your battery. During the charging process, the charger goes through three different phases. The first sees high-power charging of the battery up to approx. 80% capacity. The last 20% or so is charged at lower power as part of the second phase. The third and final phase ensures that the batteries stay fully charged. During the last phase, you can disconnect the charger from the mobility scooter.

A reliable battery charger with a long service life. There is a rubber bumper available for the Impulse II Battery Charger. The IP65 Charger is already protected against dust, and water spray - now you can protect it from accidental damage too. This rubber bumper allows it to withstand the knocks and bangs of workshop life. It will extend the life of your charger, and it has an easy-carry handle, ...or hang it from a hook when not in use. Mobility and independence are the keywords when it comes to using an electric wheelchair or scooter; the freedom to decide for yourself where to go. So of course, it’s important to be able to take your mobility scooter with you. To this end, you can rely on smart solutions from Victron Energy The multifunctional Impulse II battery charger is suitable for mobility scooters and electric wheelchairs. Most mobility scooters are fitted with two 12-volt batteries which are connected in series. Together they generate a current of 24 volts. The Impulse II is suitable for 24 volts and a variety of batteries, such as GEL batteries, AGM batteries and wet batteries. The Impulse II combines versatility with safety. For example, the battery charger has double insulation and is protected against reversed polarity, overvoltage and overheating. The Impulse II’s compact and lightweight design allows you tostore it without any problem in a shed or storage space. The charger can be quite easily moved or taken with you.   XLR plugThe Impulse II comes with a so-called “XLR plug” which is the universal standard for mobility scooters and electric wheelchairs. Specifications Input voltage: 230 VAC (range 180-265 VAC) Frequency: 50/60 Hz (range 45-65 Hz) Efficiency: 95% Power consumption in no-load operation: 0.5 W Charge voltage 'absorption': 28.8 V Charge voltage 'float': 27.6 V Charge voltage ‘storage': 26.4 V Charge algorithm: 4-stage adaptive Charge current: 8A Minimum battery capacity: 50AH Protection: Reverse polarity, output short circuit, Over temperature Weight: 1.3Kgs Dimensions (h x w x d): 60 x 105 x 190 mm Adaptive 4-stage charge algorithm: bulk – absorption – float – storageThe Impulse II charger features a microprocessor-controlled ‘adaptive’ battery management system. The adaptive feature will automatically optimize the charging process relative to the way the battery is being used. Storage mode: less maintenance and ageing when the battery is not in useThe storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode, float voltage is reduced to 2,2V/cell (26,4V for a 24V battery) to minimize corrosion of the positive plates and loss of liquid due to gassing. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulfation, a major cause of early battery failure. The Impulse II is a battery to set your mind at ease. It has a fully automated charging programme which optimises battery recharging. This 4-phase charging curve guarantees the best possible service life for your battery. During the charging process, the charger goes through three different phases. The first sees high-power charging of the battery up to approx. 80% capacity. The last 20% or so is charged at lower power as part of the second phase. The third and final phase ensures that the batteries stay fully charged. During the last phase, you can disconnect the charger from the mobility scooter. Protected against overheatingOutput current will reduce as ambient temperature increases up to more than 30°C, but the charger will not be disabled.Two LED’s for status indicationRed LED: bulk, absorptionGreen LED: float, storage en repeated absorption (refresh)Both LEDs flashing: connected with reverse polarity, short circuit, over-voltage

With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance. Bluetooth insideWith Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance. Download the Victron Bluetooth app Use a smartphone or other Bluetooth enabled device to customize settings, monitor all important data on single screen, view historical data, and to update the software when new features become available. Easy to installAll electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed. Also included are a separate front bezel for a square or round display appearance, a securing ring for rear mounting and screws for front mounting. Midpoint voltage monitoringOne bad cell or one bad battery can destroy a large, expensive battery bank. When batteries are connected in series, a timely warning can be generated by measuring the midpoint voltage. Please see the BMV manual, section 5.2, for more information. We recommend our Battery Balancer (BMS012201000) to maximize service life of series-connected lead-acid batteries. Very low current draw from the batteryCurrent consumption: 0,7Ah per month (1mA) @12V and 0,6Ah per month (0,8mA) @ 24VEspecially Li-ion batteries have virtually no capacity left when discharged until low voltage shutdown.After shutdown due to low cell voltage, the capacity reserve of a Li-ion battery is approximately 1Ah per 100Ah battery capacity. The battery will be damaged if the remaining capacity reserve is drawn from the battery. A residual current of 10mA, for example, may damage a 200Ah battery if the system is left in discharged state during more than 8 days. Bi-stable alarm relayPrevents increased current draw in case of an alarm. Other features Battery voltage, current, power, ampere-hours consumed and state of charge Remaining time at the current rate of discharge Programmable visual and audible alarm Programmable relay, to turn off non critical loads or to run a generator when needed 500 Amp quick connect shunt and connection kit shunt selection capability up to 10.000 Amps VE.Direct communication port Stores a wide range of historical events, which can be used to evaluate usage patterns and battery health Wide input voltage range: 6,5 – 70V High current measurement resolution: 10 mA (0,01A) Additional input to measure voltage (of a second battery), temperature or midpoint voltage, and corresponding alarm and relay settings